Good to see you!
Otherwise login by email.
Welcome to Dulux
Otherwise login by email.
Terms & Conditions
Registration complete
Successfully registered, please login
Registration complete
Forgotten your password?
Please enter email address associated to your account
Change Password
Password changed successfully.
Request sent!
For more tailored inspiration, please fill in the 3 questions below.
You need to answer all of the questions before submitting.
If you have concerns about your privacy?
Read our Privacy Policy.
Dulux Stellar Grey Green Zinc Phosphate Primer
Your Measurements:
Amount Needed:
For the best result we recommend to use
{coatAmount} for {productTitle}
Product Description
Dulux Stellar Grey Green Zinc Phosphate Primer is a solvent based, anti corrosion protective primer.
Suitable for use on interior and exterior ferrous and non-ferrous metalwork including steelwork, new, weathered and pre-treated zinc and galvanised iron. It may also be applied over pre-treated aluminium. Pre-treatment with an appropriate pre-treatment primer is required to ensure good adhesion
Suitable for use on interior and exterior ferrous and non-ferrous metalwork including steelwork, new, weathered and pre-treated zinc and galvanised iron. It may also be applied over pre-treated aluminium. Pre-treatment with an appropriate pre-treatment primer is required to ensure good adhesion
Application Description
Surfaces must be clean, dry, free from all defective or poorly adhering material, dirt, grease, wax etc. All surfaces should be rubbed down using a suitable abrasive paper and then dusted off. Any scrapped area should be spot primed. Light sanding on surface would ensure better subsequent intercoat adhesion.
Ferrous surfaces should be sanded or wire-brushed to remove millscale and rust. Remove the rust thoroughly and the area should be spot-primed.
For optimum performance, new galvanized and aluminium surfaces should be cleaned and degreased, then pre-treated with an appropriate pre-treatment primer to ensure good adhesion
NOTE: Ensure good ventilation during application and drying.
Ferrous surfaces should be sanded or wire-brushed to remove millscale and rust. Remove the rust thoroughly and the area should be spot-primed.
For optimum performance, new galvanized and aluminium surfaces should be cleaned and degreased, then pre-treated with an appropriate pre-treatment primer to ensure good adhesion
NOTE: Ensure good ventilation during application and drying.
Health & Safety
Treatments such as sanding, burning off etc of paint films may generate hazardous dust and/or fumes.
Wet sanding/ flatting should be used wherever possible.
Work in well ventilated areas.
Use suitable personal protection equipment.
Wear eye/hand protection.
Do not breathe vapour/ spray.
Do not eat, drink or smoke when using this product.
Use only in well-ventilated areas.
Remove as much paints as possible from brushes and rollers before cleaning.
In case of contact with eyes, rinse immediately with plenty of water and seek medical advice.
IF ON SKIN (or hair): Take off immediately all contaminated clothing.
Rinse skin with water or shower and soap or a proprietary skin cleanser. Do not use solvents or thinners.
Do not empty into water course.
Safety data sheet available for professional user on request.
In case of fire use foam, dry powder, AFFF or CO2 fire extinguisher- Never use water jet.
If medical advice is needed, have product container or label at hand.
- tds_dulux_stellar_grey_green_zinc_phosphate_primer.pdf
Tips & Advice
-
1. Preparing the SurfacesSurfaces must be clean, dry, free from all defective or poorly adhering material, dirt, grease, wax etc. All surfaces should be rubbed down using a suitable abrasive paper and then dusted off. Any scrapped area should be spot primed. Light sanding on surface would ensure better subsequent intercoat adhesion.
Ferrous surfaces should be sanded or wire-brushed to remove millscale and rust. Remove the rust thoroughly and the area should be spot-primed.
For optimum performance, new galvanized and aluminium surfaces should be cleaned and degreased, then pre-treated with an appropriate pre-treatment primer to ensure good adhesion
NOTE: Ensure good ventilation during application and drying. -
2. CleaningClean all equipment with white spirit immediately after use.
-
3. StoringKeep out of reach of children. Keep away from combustible material. Keep away from food, drinks and animal feed. Container must be in a secure, upright position and be tightly closed
How much paint do I need?
Measure the height and length of the surface you want to paint (in metres or centimetres).
Your Measurements:
{{!-- This value will be injected with JavaScript --}}
Amount needed:
{{!-- This value will be injected with JavaScript --}}
This is an estimated based on 2 coats. Actual coverage will depend on the conditions of the surface. If the colour change is strong, more coats may be required.