Weathershield

Dulux Exterior Paint Products


Dulux Weathershield A910 Line (Waterbased)


ACRYLIC EXTERIOR WALL FINISH
Dulux Weathershield Acrylic Exterior Wall Finish is a premium quality, 100% acrylic based emulsion paint.

USAGE
Dulux Weathershield Acrylic Exterior Wall Finish is suitable for new or previously painted exterior masonry surface such as brickwork, plaster, cement, rendering, and asbestos.

BENEFITS
Excellent alkali resistance and adhesion properties.
Excellent exterior durability and colour fastness.
Colourlock technology to ensure colour stay looking new for longer
Keep Cool heat reflective technology - Savings of up to 15% per annum on the energy used to cool your home and reduce exterior surface temperature by up to 5°C.
Consists of dirt resistant property which enables the finish to stay clean and brighter longer.
Protection of at least 5 years against fungus and algae growth.
Meets Malaysian Standard MS 134:2007
Singapore Green Label certified
Sirim Eco-Label certified

PACK SIZE 1, 5 and 18 litres

COLOUR RANGE Refer to Dulux Colour Inspirations.

Download Product Information

PERFORMANCE GUIDE
FILM PROPERTIES
Chemical Resistance

Water Resistance

Resistant to mild atmospheric fume attack and to the salts in new mortar, rendering and similar surfaces.
Resistant to the levels of atmospheric humidity normally experienced in exterior environment.
THEORECTICAL COVERAGE The spreading capacity of this product will vary considerably according to the roughness and porosity of the surface. On smooth surfaces of average porosity 12 - 13 m²/litre.
PRODUCT DATA
COMPOSITION(nominal) Pigment : Lightfast Non-Lead Pigments and Mineral Extenders.
Blinder : Acrylic Emulsion.
Solvent : Water
VOLUME SOLIDS White 40% (nominal), other colours will vary.
APPLICATION
THINNING
Brush or Roller


Conventional Spray
Airless Spray

For sealing new or bare surfaces, thin with up to 1 part of clean water to 10 parts of paint (10%).
For normal use, thinning is usually not necessary.
Add up to 1 part of clean water to 3 parts of paint (30%).
Ready to use. Thinning is usually not required.
SPRAY RECOMMENDATIONS
Conventional Spray
Airless Spray

Satisfactory through most equipment.
A typical set up for airless spray application would be a minimum working pressure on paint of 140Kg/cm² (2000 lb/sq in) with a spray tip size 0.58mm (23 thou) and a spray tip angle 65°
DRYING TIMES
Touch Dry
Recoat
Single coat at standard thickness:
Dependant on temperature and humidity.
2 - 3 hours.
CLEANING UP Clean all equipment with clean water immediately after use.
 
PRE - APPLICATION
SURFACE PREPARATION Surfaces must be sound, clean, dry and free from all defective or poorly adhering material, dirt, grease or wax. Remove all loose or defective paint or powdery residues by thorough brushing and scraping, using a stiff fiber brush and high pressure water jet. Treat any areas affected mould, lichens, algae and moss with Dulux Fungicidal Wash. Make good minor defects with a suitable exterior grade Filler. Surfaces that remain powdery, friable or chalky after thorough preparation should be sealed with one coat of an appropriate Primer (see below). It should not be applied on areas where moisture reading (as measured by Protimeter) exceeds 17%. These wall should be left to dry further.

Note: Do not apply Weathershield Acrylic Exterior Wall Finish during wet weather.
SYSTEM INFORMATION
Powdery Surfaces
Alkaline and New Surfaces

Normal, Sound Surfaces
PRIMER (1 COAT)
Dulux Weathershield Prime (A579-15222)
Dulux Weathershield Wall Sealer (A931 - 18177)
A thinned first coat of Weathershield (A910)
FINISH (2 COATS)
Weathershield (A910)
 
PRECAUTION
SAFETY, HEALTHY AND ENVIRONMENTAL INFORMATION
  • Keep out of the reach of children
  • Do not breathe vapour/spray
  • Use only in well ventilated areas
  • Safety data sheet available for professional user on request.
  • Avoid contact with skin or eyes
  • If swallowed seek medical advice immediately and show this container or label.
  • Dry sanding, flame cutting and/or welding of the dry paint film will give rise to dust and/or hazardous fumes. Wet [sanding]/[flatting] should be used wherever possible. If exposure cannot be avoided by the provision of local exhaust ventilation, suitable respiratory protective equipment should be used
  • Do not use empty container for storing food.
  • Remove as much paints as possible from brushes and rollers before cleaning.
  • Keep away from food, drinks and animal feed.
  • Store in a cool and shaded place.
  • Container must be in a secure, upright position and be tightly closed.
  • In case of contact with eyes, rinse immediately with plenty of water and seek medical advice.
  • In case of contact with skin wash immediately with soap and water or a proprietary skin cleanser. Do not use solvents or thinners.
  • Wear eye/hand protection.
  • Avoid release to environment. Refer to special instructions/Safety data sheet.
  • Do not empty into water course.
  • Dispose of used container in compliance with local regulation.
  • Refer to Dulux Product Safety Data Sheet for further details.
  • In case of emergency, refer to Emergency Incident Response Hotline 1-800-80-6187